Pool Care and Maintenance
PH Levels | Total Alkalinity | Calcium Hardness | Out of Balance Water | Cloudy Water | Metals | Adding Water Balance Adjustment Chemicals | Chlorine Stabilizer (100% Cyanuric Acid) | Adding Stabilizer | Pool Maintenance | What is Algae? | Preventing Algae
Proper water balance is the single most important factor to maximizing the life and appearance of any swimming pool. The following table shows ranges for basic water chemistry.
|Total Alkalinity||80-120 ppm||Weekly|
|Calcium Hardness||200-300 ppm||Monthly|
PH is the measurement of acidity of water – measured on a scale of 0 to 14 with 7 being neutral. A pH below 7.0 means the water is very acidic, as the pH approaches 8.0, the water becomes very basic (alkaline).
Not only do proper pH levels allow the other chemicals to do their work, but it is important to note that low and high levels can cause damage to a vinyl liner. Under the right circumstances with pH below 7.0, the liner can actually grow and develop unsightly wrinkles. High pH greatly accelerates the aging process and shortens the life of the liner.
Chlorine is much less effective at higher pH levels. At a pH of 8.0; chlorine is only 22% effective.
Alkalinity is a measurement of the alkaline materials dissolved in water. Alkalinity in the ideal range of 100 to 150ppm helps the pH to resist fluctuations. If the alkalinity is low it can cause a “pH bounce” causing the pH level to fluctuate in and out of the acceptable range.
Calcium Hardness refers to the amount of dissolved minerals in water. A low hardness can lead to corrosion of pool surface, filter, heater, ladder, etc. A calcium hardness level that is too high causes cloudy water and scaling (white chalky appearance).
Out of Balance Water
• Eye and skin irritation
• Unsightly wrinkles in vinyl liners
• Interferes with the efficiency of sanitizers
• Corrosion of metals (pump seals, heaters, lights, etc.)
• Cloudy water
• Scale build up (white chalky appearance) on pool surface as well as inside filter and heater
• Pitting and corrosion of gunite/concrete pools
Contaminants buildup: When swimmer wastes and other contaminants build up, the result is “combined chlorine”. Shock the pool!!!
Chemical residue: Using a calcium hypochlorite shock such as (*Shock *Sock-It *Shock-it *Burn Out *Break Out) can result in a residue build up and cloudy water. If the water looks like chalk or milk, it is usually the result of using a lot of calcium hypochlorite shock. To use this type of shock, especially in vinyl liner pools to prevent bleaching of the liner, you must:
• Fill a bucket about 1/2 full of water
• Add Shock – do not stir – let sit for a few minutes – pour only the liquid into the pool
• Discard the residue
• Do not try to dissolve the residue
Water Out of Balance: A high pH, high Total Alkaline or High Calcium Hardness will cause cloudy water. Test the water!!
Algae: Algae is a possible cause of cloudy water.
Poor Filtration: Is the filter system running a significant number of hours every day? During the swim season, the filter needs to run a minimum of 10 to 12 hours daily.
Pools with cloudy water or algae.
• Adjust pH to 7.2-7.6
• Add algaecide
• Add shock
• Add flocking agent
• Run filter 1 hour – turn off & leave off overnight
• Next day vacuum to waste
Metals: The presence of metals in the water such as iron (reddish-brown), copper (blue-green) or manganese (brown-red) can cause cloudy water. To remove the metals:
• Add 1 quart flocking agent
• Add 1 quart Majestic Blue
• Run filter 1 hour; turn off overnight
• Vacuum to waste
• When pool is completely clear, add a stain & scale preventer to remove any stains
It is not uncommon to find metals, often called free metals, dissolved in pool water. Usually they come from source water, sometimes they come as a result of the erosion of metal pool fixtures, such as heater cores.
Free metals in pool water can cause staining of pool surfaces and inhibit the performance of water sanitizers. Ideally, there should be no metals in the water: 0 ppm. If metals are detected in your water you will need a sequestering agent to render them harmless.
Adding Water Balance Adjustment Chemicals
It is best to pre dissolve a water balance adjustment chemical in a plastic bucket of pool water. Then add to the deep end of the pool or in front of a return with the pump running.
• pH Adjustment: Add recommended dosage, wait several hours and test water again.
• Alkalinity: Add at the rate of 5 lbs or less; wait about 10 minutes between each 5 lbs.
• Hardness: Add at the rate of 5 lbs. Or less; wait 30 minutes between each 5. If large amounts of calcium are needed, add over several days.
|Low pH and High Alkalinity||Adjust Alk first – Next Day pH|
|High pH Low Alkalinity||Adjust pH first – Next Day Alk|
|Low pH and Low Alkalinity||Adjust pH first – Next Day Alk|
|High pH High Alkalinity||Adjust Alk first – Next Day pH|
Testing The Water
• Follow test kit instructions (test strips are easier to use than kits)
• Use fresh reagents – shelf life for liquid reagents is only one year.
• Rinse out test cell with pool water before using.
• Retrieve water sample at elbow depth from deep end of the pool.
Most Important Pool Side Tests: Free Chlorine – pH – Total alkalinity — Free chlorine is the unused, effective chlorine that you want in your pool. — pH a number of influences can bring out rapid shifts in the pool’s pH These include:
• Swimmer wastes
• Refill water
• pH of various pool chemicals
CAL HYPO – pH 11.7
SODIUM HYPOCHLORITE – pH 13
BROMINE TABLETS – pH 3.6
SODIUM DRICHLORO – pH 6.0
LITHIUM HYPOCHLORITE – pH 10.5
CHLORINE TABLETS – pH 2.9
CHLORINE GAS – pH 2.0
With clean pool – backwash filter. Make a slurry of stabilizer and water, then add very slowly through the skimmer with the pump running continuously for at least 48 hours. Do not backwash for 3 or 4 days after adding stabilizer.
What is Algae?
Mustard Algae – Common algae in pools appears yellow-brown or “mustard” colored. It brushes off the walls of the pools easily, but quickly returns. It often rows in shady areas with poor circulation. It resists chlorine and shock treatment.
Solution – Use an algaecide along with chlorine shock. Follow label directions. Place all vacuum equipment – hose, head, pole, brushes, etc. into pool during treatment Maintain a higher than normal chlorine reading for 4 to 5 days after treatment.
Green Algae – Green algae is one of the most common problems for pools. It usually appears in corners or other areas where circulation is poor. Once established, green algae can grow explosively.
Solution – Use Algaecide along with chlorine shock. Follow label directions. It is also recommended to use a flocking agent, always vacuum to waste or drain (not backwash).
Black Algae – A very resistant form of algae that clings to the pool’s walls, floor, and cracks. The longer black algae are present, the longer it will take to get rid of it. Black algae can actually pit the mar cite finish in a gunite pool. Treat black algae as soon as it is detected. Black algae are usually found in gunite/concrete pools.
Solution – Brush algae spots vigorously with a stiff algae brush and pour algaecide along the sides where spots are visible. Run filter continuously for one hour, and then add chlorine shock to the pool. Turn off filter and leave off for several days.
Chlorine Stabilizer (100% Cyanuric Acid)
Stabilizer acts as a sun shield to extend the life of chlorine up to 3 1/2 times. It actually holds the useful form of chlorine in the pool water until needed giving longer protection against bacteria and algae. It leaves no residue – 100% soluble. “Stabilized” chlorine products (sticks – tablets – chlorine powder) contain some cyanuric acid which helps to maintain the proper level throughout the season.
|WEEKLY||Brush walls and pool floor|
|WEEKLY||Use a maintenance dose of Algaecide|
|WEEKLY||Use a maintenance dose of Majestic Blue|
|DAILY||Maintain a proper chlorine reading|
|WEEKLY||Keep properly balanced – recommended readings:Free Chlorine:1.0-2.0, pH:7.2-7.6, Total Alkalinity:80-120ppm, Hardness:200-300ppm, Stabilizer35-60ppm|